Getting Started with Tooling
This guide sets up one tool from start to finish: a 4-cavity mold, M-100, that runs on an injection molding machine,
Press 1, at 15 shots a minute. By the end, the mold is mounted, the press's runs are measured against the mold's rate,
and the mold's life is counted against a PM interval. Swap in your own machine and tool as you go.
You need an OEE-enabled machine with an item (PART-100 below) linked to it in Production Rates, and Kanoa MES 1.16 or later.
1. Let the Machine Use Tooling
- Open Configuration > Ops > Assets and select the machine in the asset tree.
- On its info tab, next to OEE Enabled, tick Uses tooling and save.
Uses tooling only shows on an OEE-enabled asset. Saving it creates the machine's Tooling tags (see
Tooling Tags).
2. Add the Tool
-
Open Configuration > Ops > Tooling and click Add a tool (+).
-
On the Details tab, enter:
Field Value Why Name M-100Unique within the site; a machine's tag mounts a tool by this name. Tooling type MoldPicking a type fills in its defaults. A Mold has positions and holds inserts. Location The press's site, or a storage location under it The site decides which machines the tool can go on. Life measured in CyclesOne cycle is one shot of the mold. PM interval 50000The mold needs a PM every 50,000 shots. Warn at % 90The mold is Due for PM at 45,000 shots. -
Click Save. The other tabs appear once the tool is saved.
See Tools and Tool Types for every field.
3. Add Its Positions
A position is one cavity, station or nest: something that makes parts each cycle.
- On the Positions tab, click Add position four times.
- Number them
1to4, set Type toCavityand Parts per cycle to1. Leave Item empty: a position with no item makes whatever item is running. - Click Save positions.
The mold now makes 4 parts per shot. Set an item on a position only for a family tool, where different cavities make different parts (see Positions).
4. Set Its Cycle Rate on the Machine
- On the Cycle Rates tab, pick
Press 1as the Machine. - Enter a Cycle rate of
15, PerMinute, and click Save rate.
The standard rate of anything the mold runs on Press 1 is now 15 shots x 4 cavities = 60 parts a minute. Positions
count parts. If the press's rate for the item is in other units, for example pounds of resin in, the
Package Count of that rate converts parts to those units. See Cycle Rates and Item Rates.
5. Say Which Item Needs It
The positions say what the mold makes; required tooling says which item needs it. Without it, Kanoa can't warn an operator who starts the wrong run, and the scheduler can't reserve the mold.
- Open Configuration > Ops > Materials and select the Required Tooling tab.
- Pick the item (
PART-100) and click Add a required tool (+). - Set Machine to
Press 1, Needs to A specific tool, Tool toM-100, leave Required ticked, and click Save.
Now starting a PART-100 run on Press 1 without M-100 mounted asks the operator to confirm, and operations scheduled
for PART-100 on Press 1 reserve M-100. See Required Tooling.
To keep M-100 on Press 1 only, add a rule on its Fits On tab: Fits A machine, On Press 1. Without
one, it fits any machine in its site that uses tooling. See Fit Rules.
6. Mount It
- Open the Operator Station for
Press 1. The info panel's Tooling card says No tooling installed. - Tap the card to open the Tooling popup, on its Mount / Unmount tab.
- Under Mount a tool, pick
M-100as the Tool, leave it On the machine, leave Mounted at empty, and click Mount.
The Tooling card now shows Tooling Installed - M-100 - 4 parts/cycle and PM 0/50,000 cycles. If the press is running, the run in progress ends and a new one starts at 60 a minute.
To mount from the PLC instead, write the tool's name to the machine's Tooling/Inputs/Tooling tag. A blank name unmounts
it. See Mounting Tools.
7. Check the Run's Rate
Run this in the Designer's Script Console, using your machine's and item's paths:
asset = system.kanoa.asset.getAssets({'assetPath': 'Enterprise\\Site\\Molding\\Press 1'})
item = system.kanoa.item.getItems({'itemName': 'PART-100'})
rate = system.kanoa.tooling.getStandardRate({
'assetId': asset.getValueAt(0, 'assetId'),
'itemId': item.getValueAt(0, 'itemId'),
})
rateList = system.kanoa.utilities.convertDatasetToJSON(rate)
for row in rateList:
for k,v in row.items():
print k,v
rateSource is cycle when the rate comes from the mold's cycle rate, tool when the item has its own rate for the mold,
and asset when the machine's own rate applies.
8. Count Its Cycles
The mold's life counts come from the machine's tags, so connect them to the PLC:
- Point
Tooling/Inputs/Cycle Countat the machine's cycle (shot) counter. Each increase is added to every tool mounted on the machine, and becomes the machine's outfeed: the cycles × the parts per cycle. Leave the asset's ownInputs/Outfeed Countunbound, so the outfeed isn't counted twice (see Tooling Tags). - Or, if the mold has its own shot counter, point
Tooling/Inputs/Tool Shot Counterat it. Its readings then count for the mold instead of the machine's cycle count.
Open the tool's Life tab to watch the counts come in. Run minutes are counted from the machine's Running time while the mold is mounted, with no tags needed.
9. Keep Up With Its Life
At 45,000 shots the mold's status changes to Due for PM, and at 50,000 to Over limit. Tools that are due or over a limit show in the tools list's Alert column, on the machine's info panel (the Tooling and Notifications cards), and in the Event Notifications widget. Mounting a tool that is over a limit asks you to confirm.
After the PM, open the Life tab, add a Note such as the work order number, and click PM done. The since-PM count goes back to 0. See Tool Life.
What's Next
- Block a cavity that stops making parts, from the mount panel. The standard rate stays the same, so the missing parts show as a speed loss with the reason Positions blocked. Retire it once it's off the machine for good. See Positions.
- Give an item its own rate for the mold if it runs slower than the mold's other items. See Cycle Rates and Item Rates.
- Put inserts in a mold base: give the base pockets, and mount each insert Into one of them. See Mounting Tools.